Bluetooth Hands-Free Preparation

Language setting

English, Spanish, and Canadian French are available. If the language setting is changed, all of the voice guidance and voice input commands are done in the selected language.

NOTE:
If the language setting is changed, device registration is maintained.

Phonebook records are not cleared, but each language has a separate phonebook.

Therefore, entries created in one language will need to be re-entered in the phonebook of the new language.

Method 1

1. Activate Bluetooth Hands-Free.

2. Say: [Beep] “Setup”.

3. Prompt: “Select one of the following: Pairing options, confirmation prompts, language, passcode, select phone or select music player.”.

4. Say: [Beep] “Language”.

5. Prompt: “Select a language: English, French, or Spanish.”.

6. Say: [Beep] “French” (Speak the desired language: “English”, “French” or “Spanish”).

7. Prompt: “French (Desired language) selected. Is this correct?”.

8. Say: [Beep] “Yes”.

9. Prompt: “French (Desired language) selected, returning to main menu” (Spoken in the newly selected language).

Method 2

1. Activate Bluetooth Hands-Free.

2. Say: [Beep] “French” (Say the desired language: “English”, “French”, or “Spanish”.) (Change the desired language by saying the language name.).

3. Prompt: “Would you like to change the language to French (Desired language) ?”.

4. Say: [Beep] “Yes”.

5. Prompt: “Please wait. Switching to French phonebook. French selected, returning to main menu” (Spoken in the newly selected language).

Device programming (Pairing)

To use Bluetooth Hands-Free, the device has to be programmed to the hands-free unit using the following procedure.

A maximum of seven devices including hands-free mobile phones and Bluetooth audio devices can be programmed to one vehicle.

NOTE:
- A device can be programmed only when the vehicle is parked.

- If a Bluetooth device has already been programmed to the vehicle as a Bluetooth audio device, it does not need to be programmed again when using the device as a hands-free mobile phone. Conversely, it does not need to be programmed again as a Bluetooth audio device if it has already been programmed as a hands-free mobile phone.

- Since the communication range of a Bluetooth equipped device is about 10 meters (32 ft), if a device is placed within a 10-meter (32 ft) radius of the vehicle, it may be detected/programmed unintentionally while another device is being programmed.

1. Activate the Bluetooth application of the device.

NOTE:
For the operation of the device, refer to its instruction manual.

2. Activate Bluetooth Hands-Free.

3. Say: [Beep] “Setup”.

4. Prompt: “Select one of the following: Pairing options, confirmation prompts, language, passcode, select phone or select music player.”.

5. Say: [Beep] “Pairing options”.

6. Prompt: “Select one of the following: Pair, edit, delete, or list.”.

7. Say: [Beep] “Pair”.

8. Prompt: “Please say a 4-digit pairing code.”.

9. Say: [Beep] “XXXX” (Speak an arbitrary 4-digit pairing code. This can be any combination of 4 numbers.).

NOTE:
Record the code as it will be used to program your device in Step 16.

10. Prompt: “Pairing code XXXX (4- digit number). Is this correct?”.

11. Say: [Beep] “Yes” or “No”.

12. If “Yes”, go to Step 13.

If “No”, the procedure returns to Step 8.

13. Prompt: “Start pairing procedure on the device. See the device manual for instructions.”.

14. Using the device, perform a search for the Bluetooth device (Peripheral device).

NOTE:
For the operation of the device, refer to its instruction manual.

15. Select “Mazda” from the device list searched by the device.

16. Input the 4-digit pairing code set in Step 9 to the device.

17. Prompt: “Please say the name of the device after the beep.”.

18. Say: [Beep] “XXXX - - -” (Speak a “device tag”, an arbitrary name for the device.).

Example: “Stan's device.”

NOTE:
Speak a programmed “device tag” within 10 seconds.

If more than two devices are to be programmed, they cannot be programmed with the same or similar “device tag”.

19. Prompt: “Adding XXXXXX - - - (Ex. “Stan's device”) (Device tag). Is this correct?”.

20. Say: [Beep] “Yes”.

21. Prompt: “Pairing complete”.

After a device is registered, the system automatically identifies the device. By activating Bluetooth Hands-Free again, or by activating Bluetooth Hands-Free first after switching the ignition from off (LOCK) to ACC, the system reads out a voice guidance, “XXXXXX - - - (Ex.

“Stan's device”) (Device tag) is connected”.

NOTE:
Device registration can also be done by operating the audio unit or panel buttons on the navigation unit. Refer to “Bluetooth Audio Preparation” (For audio unit) or the separate manual “NAVIGATION SYSTEM” (For navigation unit).

Making a Call Using a Telephone Number

1. Activate Bluetooth Hands-Free.

2. Say: [Beep] “Dial”.

3. Prompt: “Number, please”.

4. Say: [Beep] “XXXXXXXXXXX (Ex.

“555-1234”) (Telephone number)”.

5. Prompt: “Dialing XXXXXXXXXXX (Ex. “555-1234”) (Telephone number) is this correct?”.

6. Say: [Beep] “Yes” or “No”.

7. When “Yes” is spoken, the procedure proceeds to Step 8.

When “No” is spoken, the procedure returns to Step 3.

8. Prompt: “Dialing”.

Receiving an Incoming Call

1. Prompt: “Incoming call, press the pickup button to answer”.

2. To accept the call, press the pick-up button.

To reject the call, press the hang-up button.

Hanging Up a Call

Press the hang-up button during the call.

Beep will confirm that call is ended.

Volume Adjustment

Turn the power/volume dial of the audio unit or navigation system to adjust the volume.

Turn the power/volume dial to the right to increase volume, to the left to decrease it.

NOTE:
- The volume can also be adjusted using the volume button on the steering wheel.

- The music volume of the audio unit and the navigation system cannot be adjusted while Bluetooth Hands-Free is being used.

Voice Guidance Interrupt Operation

Voice guidance can be stopped by pressing the talk button (Short press) while it is being heard. A new voice input command can then be spoken by the user.

· Press the talk button (Short press).

Help Function Use

The help function informs the user of all the available voice commands under the current conditions.

1. Press the talk button (Short press).

2. Say: [Beep] “Help”.

3. Follow the prompts to receive the appropriate voice guidance instructions.